- Accueil
- Produits
- ATE / Bench Calibrators & Multimeters
- 5075 : Multimètre Numérique de Précision
5075 : Multimètre Numérique de Précision
Caractéristiques Principales
- Résolution 7 digits
- 10nV à 10kV, 10pA à 30A
- Résistance, capacité, fréquence
- Haute précision
- Interface GPIB
- Scanner 10 voies en option
- Contrôle via logiciel EasyCal
Multimètre numérique de table combinant hautes performances avec simplicité d’utilisation. Le 5075 mesure de la gamme des nanovolts jusqu’à 10kV, des pico-ampères jusqu’à 30A, des micro-ohms jusqu’à 1GΩ, des picofarads jusqu’à 300µF, avec une précision de 7,5 digits.
L'étalonnage facile
Connectez le 5075 à un PC/portable (via RS233, GPIB ou USB) équipé du logiciel Time Electronics EasyCal et automatisez le processus d'étalonnage. Augmentez la vitesse d'étalonnage et la cohérence des résultats et produisez des certificats et rapports d'étalonnage suivant les normes de qualité ISO 9001.Technical Specifications
Accuracy specified as ± ppm reading + ± Floor at default resolution (shown in brackets), relative to calibration standards. TCAL = 20°C
DC Voltage Range Resolution (at default in brackets) 90 Day ± 5°C 1 Year ± 5°C 0 to 3mV / 0 to 10mV
10nV (10nV)
22 + 80nV
30 + 80nV
0 to 30mV / 0 to 100mV
10nV (100nV)
22 + 800nV
30 + 800nV
0 to 300mV
0 to 1V100nV (1μV)
22 + 8μV
12 + 6μV30 + 8μV
18 + 6μV0 to 3V / 0 to 10V
1μV (10μV)
12 + 60μV
18 + 60μV
0 to 30V / 0 to 100V
10μV (100μV)
20 + 600μV
30 + 600μV
0 to 300V / 0 to 1kV
100μV (1mV)
22 + 8mV
30 + 8mV
0 to 3kV / 0 to 10kV
1mV (10mV)
250 + 1V
350 + 1.2V
All DCV specifications ± 0.4μV
DC Current Range Resolution (at default in brackets) 90 Day ± 5°C 1 Year ± 5°C 0 to 3μA / 0 to10μA 10pA (10pA) 150 + 200pA 200 + 250pA 0 to 30μA / 0 to 100μA 100pA (100pA) 75 + 1nA 100 + 1nA 0 to 300μA / 0 to 1mA 100pA (1nA) 75 + 10nA 100 + 10nA 0 to 3mA / 0 to 10mA
1nA (10nA)
75 + 100nA
100 + 100nA
0 to 30mA / 0 to 100mA 10nA (100nA) 75 + 1μA 100 + 1μA 0 to 300mA / 0 to 1A 100nA (1μA) 150 + 10μA 200 + 10μA 0 to 3A / 0 to 10A 10μA (10μA) 500 + 200μA 750 + 200μA 0 to 30A 100μA (100μA) 500 + 2mA 750 + 2mA AC Voltage Range Resolution* 90 Day ± 5°C 1 Year ± 5°C 0 to 30mV 1μV 0.05% + 4μV 0.06% + 4μV 0 to 300mV 10μV 0.05% + 40μV 0.06% + 40μV 0 to 3V 100μV 0.05% + 400μV 0.06% + 400μV 0 to 30V 1mV 0.05% + 4mV 0.06% + 4mV 0 to 300V 10mV 0.15% + 0.1V 0.2% + 0.12V 0 to 3kV 100mV 0.15% + 1V 0.2% + 1.2V * Voltage AC + DC / Current AC + DC
Total measurement error will not exceed the sum of the separate AC + DC accuracy specification, plus one display digit.All AC Voltages ± 50μV
AC Current Range Resolution* 90 Day ± 5°C 1 Year ± 5°C 0 to 30μA 1nA 0.1% + 8nA 0.2% + 10nA 0 to 300μA 10nA 0.1% + 80nA 0.2% + 100nA 0 to 3mA 100nA 0.1% + 800nA 0.2% + 1μA 0 to 30mA 1μA 0.1% + 8μA 0.2% + 10μA 0 to 300mA 10μA 0.1% + 80μA 0.2% + 100μA 0 to 3A 100μA 0.15% + 1mA 0.2% + 1mA 0 to 30A 1mA 0.15% + 10mA 0.2% + 10mA * Voltage AC + DC / Current AC + DC
Total measurement error will not exceed the sum of the separate AC + DC accuracy specification, plus one display digit.All AC Current ± 50nA
Resistance Range Resolution (at default in brackets) 90 Day ± 5°C 1 Year ± 5°C 0 to 30mΩ / 0 to 100mΩ 10nΩ (100nΩ) 70 + 2μΩ 100 + 2.5μΩ 0 to 300mΩ / 0 to 1Ω 100nΩ (1μΩ) 40 + 10μΩ 60 + 15μΩ 0 to 3Ω / 0 to 10Ω 1μΩ (10μΩ) 30 + 80μΩ 40 + 100μΩ 0 to 30Ω / 0 to100Ω 10μΩ (100μΩ) 20 + 600μΩ 30 + 800μΩ 0 to 300Ω / 0 to 1kΩ 100uΩ (1mΩ) 20 + 6mΩ 30 + 8mΩ 0 to 3kΩ / 0 to 10kΩ 1mΩ (10mΩ) 20 + 60mΩ 30 + 80mΩ 0 to 30kΩ / 0 to 100kΩ 10mΩ (100mΩ) 30 + 600mΩ 45 + 800mΩ 0 to 300kΩ / 0 to 1MΩ 100mΩ (1Ω) 60 + 8Ω 90 + 10Ω 0 to 3MΩ / 0 to 10MΩ 1Ω (10Ω) 100 + 100Ω 150 + 120Ω 0 to 30MΩ / 0 to 100MΩ 100Ω (100Ω) 750 + 10kΩ 1000 + 10kΩ 0 to 300MΩ / 0 to 1GΩ 10kΩ (10kΩ) 0.5% + 1MΩ 0.75% + 1MΩ 2 wire ranges begin at 300mΩ. Accuracy applies to 2 and 4 wire resistances
PRT (PT100) Temperature Range Resolution 90 Day ± 5°C 1 Year ± 5°C -200 to +600°C 0.001°C 0.05°C 0.06°C NOTE: Only available in four terminal mode on the 300Ω range.
Frequency Range Resolution 90 Day ± 5°C 1 Year ± 5°C 0 to 100kHz 1Hz 10 + 1 12 + 1 NOTE: Frequency may be measured on either voltage or current inputs if the AC option has been fitted.
Capacitance Range Resolution (5 digit) 90 Day ± 5°C 1 Year ± 5°C 0 to 30nF 1pF 0.2% + 20pF 0.25% + 20pF 0 to 300nF 10pF 0.2% + 200pF 0.25% + 200pF 0 to 3μF 100pF 0.2% + 2nF 0.25% + 2nF 0 to 30μF 1nF 0.2% + 20nF 0.25% + 20nF 0 to 300μF 10nF 0.2% + 200nF 0.25% + 200nF All Capacitances ± 1pF
Accuracy stated as 90 day and 1 year specification for all ranges ± 5°C in 6 digit mode for DC and 6 digit mode for AC.
Operation SpecificationsBasic Functions N Digits Changes the reading resolution, which can be changed from 4 up to 7 digits, (depending on the scale selected). Null Null facility is available on all DC ranges, Ohms and Capacitance. Null is not available on AC or frequency. When this key is pressed, the DMM will accept the measured present value as the zero value for the range selected. If auto-range is on, the unit will null each range. This is useful for cancelling an offset voltage or for zeroing the value of the test leads on resistance. Auto Ranging Auto-range (AUTO) will select the optimum range for the measurement. This will introduce very little delay for the operator. The indicator above the keypad will show when the DMM is in auto-range mode. Filter The filter alters the integration time of the reading. Filter times are 150ms, 250ms, 500ms, 1s, 2s, 4s, 8s, 16s, 32s & off. Internal Temperature Internal Temperature controlled at 35˚C ± 2˚C with an ambient temperature of 20 to 28˚C Advanced Functions Ohms Compensation Cancels the effects of any offset voltages by first measuring the input voltage with the current source on and the measuring the voltage with the current source off. The induced voltage is the difference between the two voltages, thus giving a more accurate reading. Can be used in 2 and 4 wire mode for measurements up to 100kΩ. Ohms compensation doesn’t work on ranges above 100kΩ. Diode / Zener Diode Test The diode test function will passes a current of 1mA through the diode under test and displays the diode forward voltage. May be used for zener diodes up to 10V. Self Test Reset The instrument can perform a self-test of all its digital circuits including the IEEE and RAM. Max – Min This function displays the maximum and minimum readings of the input. By using the up and down keys the Maximum, Minimum or Present value input may be displayed. Peak Hold This function will display the peak value measured. By using the up and down keys the Peak value or Present input may be displayed. Component Test Used for component selection. If a component to be tested must fall between a high and low value, component test can be used to make the selection process quicker. It provides a visual display which moves a pointer between the high and low values input, and also indicates whether the component is higher or lower in value than the high and low points if it doesn’t fall between them. PRT Temp
PT100 elements can be measured and displayed in ˚C using this function.
Dual Display Display Voltage and frequency of the input or the current and frequency (if the AC module has been installed), for AC inputs. Analogue Filter The analogue filter can be switched into the input circuit to remove any high frequency noise that may be present on the input. Auto Dynamic Filter: The Auto dynamic filter automatically selects the most appropriate filter period. The auto dynamic filter will increase or decrease the filter period (up to the maximum set using the filter key) depending upon the stability of the input signal. Continuity / Sample Beep Continuity tests can be performed by selecting this option when in resistance mode. Any value below 30% of the full range will produce the continuity beep. Sample beep alerts the operator to a new reading being displayed. Internal Date / Time Date and Time can be displayed or entered using this option. Internal Temp
The internal temperature of the 5075 can be displayed and is updated approximately every 5 minutes. The internal temperature is used to perform an internal calibration when the temperature varies by 1˚C, thus insuring the temperature coefficient of the unit remains negligible.
Remote Control
This instrument implements the requirements of the IEEE - 488/1978 standard. The IEEE - 488 interface, allows remote control of the instrument by a suitable computer or controller. Repetitive calibration work can be speedily and accurately carried out, giving printed results if required. The main limitations of the IEEE are :-
1) A maximum of 15 devices on the bus.
2) The maximum bus length should not be greater than 20m or number of devices x 2, which ever is the shorter.
Scanner Option
The scanner option for the 5075 DMM consists of an internally fitted relay board. This board provides 10 input channels. Up to two boards may be fitted giving up to 20 channels. The relays switch all 4 input terminals: V+, V-, I+, I– to one of 10/20 inputs via the 25 way ‘D’ connectors. The scanner card may be used for voltage, current, resistance, capacitance, frequency, and PT100.
Scanner Specifications
Maximum voltage: 200V DC / 150V AC Maximum current: 1A DC / 1A AC
Thermal EMF: Less than 2μV per contact Contact resistance: Less than 150mΩ
Operating life: Up to 200 million operations Operating time: 20ms
General SpecificationsOperating Temperature 0 to 50˚C Line Power 110/220/240V AC, 50/60Hz Standard Interfaces GPIB (USB adaptor optional) Dimensions W423 x H89 x D415mm Weight 8.5kg Country of Origin UK Models 5075
Multimètre Numérique de Précision
Options 9726
10 canaux Scanner
9728 Kit de montage rack 19” C162 Certificat de Calibration Usine C130 Certificat de Calibration UKAS (ISO 17025) Calibration Software and Accessories ECFLA
Logiciel EasyCal
9795
Kit d'imprimante et extras - Voir Fiche technique
9777 Lecteur de code-barres - Voir Fiche technique 9778 Imprimante d'étiquettes - Voir Fiche technique 9597 Cable GPIB 9743 PCI - GPIB carte d'interface 9794
Adaptateur USB - GPIB
Téléchargements PDF Nom du fichier Taille du fichier Langue 460kB
EN
4MB (low resolution)
EN
8MB (Higher resolution)
EN
Appel d'offre
5075 : Multimètre Numérique de Précision
Produits connexes
-
5018 : Calibrateur de Tension / Courant AC/DC
- Précision 15ppm
- Résolution 0,5ppm
- Tension DC 20mV-200mV-2V-20V
- Fonction rampe
- Interfaces RS232/GPIB/USBaces
- Idéal pour les applications ATE
- Contrôle via logiciel EasyCal
-
5025C : Calibrateur Multifonction
- 15 ppm pour métrologie
- Calibrer multimètres
- 11 fonctions standard
- 0 - 1050V & 0 - 22A (AC/DC)
- Capacité & resistance
- Simulation Thermocouple/PT100
- Étalonnage de puissance
-
5051 Plus : Système de Calibration Multifonctions
- Calibrateur / multimètre / PC
- 0 - 1050V & 0 - 22A (AC / DC)
- Source à la résistance 1GΩ
- Thermocouple simulation / mesure
- PT100, la capacité, l'inductance
- Calibration de pinces
- Logiciel EasyCal inclus
-
5065 : Multimètre Numérique
- Résolution 6,5 digits
- Précision 0,005% en tension DC
- Interfaces RS232 et USB
- Interface GPIB en option
- Mesures de température
- Carte scanner 10 voies en option
- Contrôle via logiciel EasyCal
-
Logiciel EasyCal
- Automate the calibration process
- Control TE calibrators & DMMs
- Automated planning & scheduling
- For use with multiple devices
- 1200+ cal procedures included
- Management/admin features
- Easily produce certificates & reports